Linux Mint Türkiye
Linux Mint Destek => Donanım => Yazıcılar & Tarayıcılar => Konuyu başlatan: mehmethanifi - 04 Haziran 2015, 16:08:51
-
Merhabalar,
Ağda bulunan tarayıcı özelliği olan bir yazıcıdan tarama yapmam gerekiyor. Nasıl yapabilirim.
Yazıcıyı bilgisayra kurdum çıktı alabiliyorum. Yazıcı bu arada network yazıcı. Canon MF 4800
Teşekkürler.
-
Menüye "Basit Tarama" ya da "tarama" yazarak çıkan sonuçlardan Simple Scan aracını açarak deneme yapabilirsiniz.
-
hocam onu yapmıştım.
(http://i.hizliresim.com/PqGR59.png) (http://hizliresim.com/PqGR59)
-
sudo gedit /etc/default/saned komutuyla açılan dosyada
# Set to yes to start saned
RUN=yes
kısmını bulun, RUN değişkeninin karşısına yes yazıp kaydedin. Ardından sudo gedit /etc/sane.d/net.conf komutuyla açılan dosyanın altına yazıcının bağlı olduğu IP adresini yazın. Örnek resim:
(https://farm6.staticflickr.com/5581/14777977880_c865b0df95_z.jpg)
İlgili servisi bu komutla yeiden başlatın:
sudo service saned restart Bu işlemlerden sonra çalışıp çalışmadığını scanimage -L komutuyla kontrol edebilirsiniz. Yazıcı adı ve modeli görüntüleniyorsa tarayıcı algılanmış demektir.
Eğer Mate kullanıyorsanız komutlarda gedit yazan yere pluma, KDE kullanıyorsanız gedit yazan yere kate yazmalısınız.
Kaynak:http://xmodulo.com/configure-network-printer-scanner-ubuntu-desktop.html (http://xmodulo.com/configure-network-printer-scanner-ubuntu-desktop.html)
-
hocam çıktı şu şekildedir.
scanimage -L
No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).Tekrar komutları deneyince
scanimage -L
Parçalama arızası
-
hocam çıktı şu şekildedir.
scanimage -L
No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).Tekrar komutları deneyince
scanimage -L
Parçalama arızası
Peki şimdi bast tarama aracı çalışıyor mu?
-
yok hocam çalışmıyor.
-
yok hocam çalışmıyor.
# Set to yes to start saned
RUN=yes
bölümü önceki iletide tek satır gibi görünüyordu. Düzelttim. Sizin dosyada iki ayrı satır halinde görünüyor değil mi?
-
Alternatif olarak Vuescan (http://www.hamrick.com/vuescan/canon_mf4800.html) denenebilir.
-
indirip denedim hocam ama oda görmedi.
-
Buradan (http://www.canon-europe.com/support/consumer_products/products/fax__multifunctionals/laser/laserbase_mf_series/i-sensys_mf4870dn.aspx?type=download&language=EN&os=Linux) sürücüsünü indirip içindeki paketler ile sürücü kurulumunu denemiş miydiniz?
-
Evet hocam denedim ama scanner ile ilgili bir paket bulamadım. Print alınıyor yazıcıdan.
-
sudo gedit /etc/sane.d/saned.confkomutuyla açılan dosyada ## Access list yazısını bulun. Alt satıra geçip 192.168.0.0/24 yazın. Dosyayı kaydedip kapatın. Çalışmazsa scanimage -L çıktısına tekrar bakalım.
-
scanimage -L
No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).
-
Bu yazıcı doğrudan ağa mı bağlı? Yoksa bir bilgisayara mı bağlı? O bilgisayar üzerinden mi paylaşılıyor? Yazıcının modeli tam olarak nedir?
-
Hocam Canon MF 4800 network yazıcı. Yazıcının driveri pc de yüklü. Print alabiliyoruz.
-
MF4375 gibi bir sayı yok mu? MF4000 diye bir yazıcı bulamadım. Yazıcınız şu listedekilerden biri değil mi? http://www.sane-project.org/sane-mfgs.html#Z-CANON
-
isensy mf 4870 dn hocam.
-
sudo su komutunu verip şifrenizi girin. Ardından scanimage -L çıktısını tekrar paylaşınız. Önceden olduğu gibi yazıcı bulunamazsa sorun nasıl çözülür bilmiyorum.
-
scanimage -L
No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).
ilgiliniz için çok teşekkür ederim hocam. sizlerede zahmet veriyoruz. umarım sorunu çözebilirim. Çözersem mutlaka paylaşımda bulunacağım.
-
Bu tarayıcının SANE (Scanner Access Now Easy) desteği yok sanırım.
http://www.sane-project.org/sane-mfgs.html#Z-CANON (http://www.sane-project.org/sane-mfgs.html#Z-CANON)
SANE'nin depoda 1.0.23 sürümü mevcut, ama aşağıdaki komutlar ile PPA deposundan 1.0.25 sürüme güncelleme yaparak şansınızı deneyebilirsiniz.
sudo add-apt-repository ppa:rolfbensch/sane-git
sudo apt-get update
Yukarıdaki komutlar ile depoyu ekledikten sonra Güncelleme Yöneticisini açınız ve Yenile düğmesine bastıktan sonra sisteminizi güncellemeyi deneyiniz.
-
scanimage -L
device `pixma:MF4800_10.60.0.17' is a CANON Canon i-SENSYS MF4800 Series multi-function peripheral
(http://i.hizliresim.com/OqlAVz.png) (http://hizliresim.com/OqlAVz)
-
Yeni sürümde destek eklenmiş. Ancak ethernet sorunu olduğu yazıyor. Bir de şu dosyayı değiştirerek bağlanmayı deneyebilirsiniz:
sudo gedit /etc/sane.d/pixma.confAçılan dosyada bjnp ile başlayan satırlardan birinin önündeki # işaretini silin, ardından yazıcının IP adresini yazın. Dosyayı kaydedip kapatın.
Örnek: bjnp://10.0.1.4
Bu şekilde olmazsa yazıcının bağlandığı port numarasını ip adresinin sonuna eklemek denenebilir:
bjnp://10.0.1.4:8612
-
iki şekilde de denedim hocam ama olmadı.
-
Araştırdım ancak bir şey bulamadım. Bir de geliştiricilere sorabiliriz. Şu çıkıtıları paylaşırsanız e-posta yollayıp sorabilirim. Gelişmeleri doğrudan takip etmek, geliştiricilere birinci ağızdan bilgi vermek için siz de sorabilirsiniz.
cat /etc/default/sanedcat /etc/sane.d/net.confcat /etc/sane.d/saned.confcat /etc/sane.d/pixma.confscanimage -LYazıcıyı bilgisayara bağladıktan sonra
lsusbE-posta adresi:sane-devel@lists.alioth.debian.org
E-posta listesini takip etmek için şuradan kayıt olabilirsiniz: http://lists.alioth.debian.org/mailman/listinfo/sane-devel
-
cat /etc/sane.d/net.conf
# This is the net backend config file.
## net backend options
# Timeout for the initial connection to saned. This will prevent the backend
# from blocking for several minutes trying to connect to an unresponsive
# saned host (network outage, host down, ...). Value in seconds.
# connect_timeout = 60
## saned hosts
# Each line names a host to attach to.
# If you list "localhost" then your backends can be accessed either
# directly or through the net backend. Going through the net backend
# may be necessary to access devices that need special privileges.
10.60.0.17
cat /etc/default/saned
# Defaults for the saned initscript, from sane-utils
# Set to yes to start saned
RUN=yes
# Set to the user saned should run as
RUN_AS_USER=saned
at /etc/sane.d/saned.conf
# saned.conf
# Configuration for the saned daemon
## Daemon options
# Port range for the data connection. Choose a range inside [1024 - 65535].
# Avoid specifying too large a range, for performance reasons.
#
# ONLY use this if your saned server is sitting behind a firewall. If your
# firewall is a Linux machine, we strongly recommend using the
# Netfilter nf_conntrack_sane connection tracking module instead.
#
# data_portrange = 10000 - 10100
## Access list
10.60.0.0/24
# A list of host names, IP addresses or IP subnets (CIDR notation) that
# are permitted to use local SANE devices. IPv6 addresses must be enclosed
# in brackets, and should always be specified in their compressed form.
#
# The hostname matching is not case-sensitive.
#scan-client.somedomain.firm
#192.168.0.1
#192.168.0.1/29
#[2001:db8:185e::42:12]
#[2001:db8:185e::42:12]/64
# NOTE: /etc/inetd.conf (or /etc/xinetd.conf) and
# /etc/services must also be properly configured to start
# the saned daemon as documented in saned(8), services(4)
# and inetd.conf(4) (or xinetd.conf(5)).
cat /etc/sane.d/pixma.conf
# pixma.conf configuration for the sane pixma backend
#
# define URI's of scanners (one per line)
# This is only used for network scanners.
# normally scanners will be detected by sending a broadcast
# if this does not work under your OS, or if the scanners
# are on a different subnet, configure your scanners URI here
#
# method must be bjnp
# port number can normally be left out, port 8612 is used as default
# Example:
bjnp://10.60.0.17
# bjnp://printer-1.pheasant.orgscanimage -L
[bjnp] udp_command: ERROR - no data received
[bjnp] bjnp_init_device_structure: Cannot read mac address, skipping this scanner
[bjnp] udp_command: ERROR - no data received
[bjnp] add_scanner: ERROR - Cannot read scanner make & model: bjnp://10.60.0.17
Parçalama arızasılsusb
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 004: ID 04f2:b32f Chicony Electronics Co., Ltd
Bus 001 Device 003: ID 0489:e036 Foxconn / Hon Hai
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 002: ID 09da:054f A4 Tech Co., Ltd
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-
[member=1676]mehmethanifi[/member] Son komutta yazıcı listede görünmüyor. Yazıcı bilgisayara bağlıydı değil mi?
-
Hocam network yazıcı olduğu için doğrudan bağlı değil. ip ile tanımlı. print alabiliyorum.
-
Hocam network yazıcı olduğu için doğrudan bağlı değil. ip ile tanımlı. print alabiliyorum.
Evet, öyle olduğunu daha önce de sormuştum. Ancak benim aradığım yazıcının 8 haneli tanımlayıcısı(8087:0024 bunun gibi). Geliştiricilerin işine yarayacağını düşündüğümden doğrudan bilgisayara bağlayıp çıktıyı istemiştim. E-postaya henüz bir cevap gelmedi. İsterlerse yollarız.Yazıcıyı bilgisayara bağladıktan sonra
lsusb
-
Buradaki (http://blogs.fsfe.org/the_unconventional/2014/09/09/network-sane/) adımları da eklemeyi deneyelim.
Aşağıdaki komut ile eksik olabilecek paketleri yükleyiniz.
sudo apt-get install avahi-daemon libnss-mdns sane-utils
Aşağıdaki komut ile group ayarlarını yapınız.
sudo usermod -a -G lp,scanner saned
-
eger yazıcıda smb özelligi varsa yazıcının ip sini yazıp yazıcı ayarlarından smb ayarlarını yapman gerekiyor en azından kyocerada ordan yapılıyor ama canonda aynıdır diye düşünüyorum pc de tarama diye bir klasör açıp paylaşıma açıyorsun smb ayarlarından admin bir kulanıcıyla smb ayarlarını yapmanız gerekiyor taradığınız dosya paylaşılmış klasöre yönlenecektir
-
[member=1676]mehmethanifi[/member] Konunun üzerinden 1 yıldan fazla zaman geçti. Eğer hâlâ aynı sıkıntı yaşanıyorsa şu öneri de denenebilir:
https://support.usa.canon.com/kb/index?page=content&id=ART109227
Canon yazıcılar ağ üzerinden yazma işlemi için 8611, tarama işlemi için 8612 nolu portların açık olmasına ihtiyaç duyuyormuş. İlgili portları açmak için:
sudo ufw enable
sudo ufw allow 8612/tcp
sudo ufw allow 8612/udpPortların eklenip eklenmediğini kontrol etmek için:
sudo ufw status