arkadaşlar merhaba
ben yepyenii bir linux kullanıcıyım , henüz aldığım tulpar t7 v9.1 bilgisayarıma linux mint 18 kurdum lakin ekran kartıyla sürekli sorun yaşıyorum. bazen ekran kartım hiç görmüyor. glxgears testinde 75fps de alıyorum 5500 de alıyorum. fakat ekran kartı devreye girse bile ekranda yırtılmalar yaşanıyor. yardımcı olabilir misiniz ? ekran kartım gtx1070, işlemcim 6700k...
lspci | egrep 'VGA|3D|Display'
dediğimde sadece
01:00.0 VGA compatible controller: NVIDIA Corporation Device 1be1 (rev a1)
yazıyor.
glxinfo
dediğimde ise
name of display: :0
Error: couldn't find RGB GLX visual or fbconfig
yazıyor.
bir de nvidia x server ekran kartımın sıcaklığını falan göstermiyor ekran kartımı göremiyor dün kapamadan önce görünüyordu bugün tekrar gitmiş.
konu daha önce açıldı mı diye baktım ama bulamadım eğer varsa acemiliğime verin şimdiden teşekkür ederim.
not*: kurtarın beni windows ve hatta windows 10dan
atakan[member=2886]Atakan[/member]-TULPAR-T7-V9-1 ~ $ dpkg -l | egrep 'nvidia|bumblebee|primus|prime|virtualgl|fglrx'
ii nvidia-367 367.57-0ubuntu0.16.04.1 amd64 NVIDIA binary driver - version 367.57
ii nvidia-opencl-icd-367 367.57-0ubuntu0.16.04.1 amd64 NVIDIA OpenCL ICD
ii nvidia-prime 0.8.2linuxmint1 amd64 Tools to enable NVIDIA's Prime
ii nvidia-settings 361.42-0ubuntu1 amd64 Tool for configuring the NVIDIA graphics driver
ii primus-libs:amd64 0~20150328-1 amd64 Shared libraries for primus
ii primus-libs:i386 0~20150328-1 i386 Shared libraries for primus
ii primus-libs-dbg:amd64 0~20150328-1 amd64 Shared libraries for primus - debugging symbols
ii primus-libs-ia32:i386 0~20150328-1 i386 Shared libraries for primus (32-bit)
# Configuration file for Bumblebee. Values should **not** be put between quotes
## Server options. Any change made in this section will need a server restart
# to take effect.
[bumblebeed]
# The secondary Xorg server DISPLAY number
VirtualDisplay=:8
# Should the unused Xorg server be kept running? Set this to true if waiting
# for X to be ready is too long and don't need power management at all.
KeepUnusedXServer=false
# The name of the Bumbleblee server group name (GID name)
ServerGroup=bumblebee
# Card power state at exit. Set to false if the card shoud be ON when Bumblebee
# server exits.
TurnCardOffAtExit=false
# The default behavior of '-f' option on optirun. If set to "true", '-f' will
# be ignored.
NoEcoModeOverride=false
# The Driver used by Bumblebee server. If this value is not set (or empty),
# auto-detection is performed. The available drivers are nvidia and nouveau
# (See also the driver-specific sections below)
Driver=
# Directory with a dummy config file to pass as a -configdir to secondary X
XorgConfDir=/etc/bumblebee/xorg.conf.d
## Client options. Will take effect on the next optirun executed.
[optirun]
# Acceleration/ rendering bridge, possible values are auto, virtualgl and
# primus.
Bridge=auto
# The method used for VirtualGL to transport frames between X servers.
# Possible values are proxy, jpeg, rgb, xv and yuv.
VGLTransport=proxy
# List of paths which are searched for the primus libGL.so.1 when using
# the primus bridge
PrimusLibraryPath=/usr/lib/x86_64-linux-gnu/primus:/usr/lib/i386-linux-gnu/primus
# Should the program run under optirun even if Bumblebee server or nvidia card
# is not available?
AllowFallbackToIGC=false
# Driver-specific settings are grouped under [driver-NAME]. The sections are
# parsed if the Driver setting in [bumblebeed] is set to NAME (or if auto-
# detection resolves to NAME).
# PMMethod: method to use for saving power by disabling the nvidia card, valid
# values are: auto - automatically detect which PM method to use
# bbswitch - new in BB 3, recommended if available
# switcheroo - vga_switcheroo method, use at your own risk
# none - disable PM completely
# https://github.com/Bumblebee-Project/Bumblebee/wiki/Comparison-of-PM-methods
## Section with nvidia driver specific options, only parsed if Driver=nvidia
[driver-nvidia]
# Module name to load, defaults to Driver if empty or unset
KernelDriver=nvidia-current
PMMethod=auto
# colon-separated path to the nvidia libraries
LibraryPath=/usr/lib/nvidia-current:/usr/lib32/nvidia-current
# comma-separated path of the directory containing nvidia_drv.so and the
# default Xorg modules path
XorgModulePath=/usr/lib/nvidia-current/xorg,/usr/lib/xorg/modules
XorgConfFile=/etc/bumblebee/xorg.conf.nvidia
## Section with nouveau driver specific options, only parsed if Driver=nouveau
[driver-nouveau]
KernelDriver=nouveau
PMMethod=auto
XorgConfFile=/etc/bumblebee/xorg.conf.nouveau
bir de her açışımda yazılımsal görsel işleme kipinde çalışıyor diyor bundan nasıl kurtulurum ?
